• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, the wear and tear could cause lock malfunctions. There are a few simple steps you can take to restore the security of your uPVC door.

These simple fixes will make your home safer, whether you realign the lock or clean the locking mechanism.

Clean the Lock

Although patio doors are a great option to let in the outside and keep the elements out but they can also pose an issue for security when your lock isn't functioning as it should. With time, wear and tear, hot and cold weather dirt and debris can cause damage to your patio door's lock and make it difficult to open. Fortunately, with a little care, you can ensure your patio door's locks always work correctly.

To begin with, it's important to clean the lock of your patio door and all the moving parts. This will help flush out any accumulated grime and coatings that could hinder the lock from functioning in the way it should. Begin by wiping down all the moving parts of the lock for your Patio Door Lock Repair door with a damp cloth. Then you can use a scouring paper or a rough damp cloth to scrub the dirt-infested parts of the frame and door. Then, wipe the entire lock using a dry cloth to remove any remaining dampness, and allow it to dry completely before making use of it again.

If you have a patio door that uses a pin tumbler latch mechanism it is possible to apply lubrication to the lock by applying graphite powdered to the key or applying a lubricant made of Teflon, such as WD-40 Multi-Use Product. This kind of lubricant is easy to apply and it won't disintegrate as time passes. If you're unable find the right lubricant to use with your lock, you can apply a pencil that has a thicker tip. Insert the pencil into the lock and jiggle it around a bit to distribute the graphite.

Regular maintenance is also required to keep the tracks of sliding patio door repair service near me patio doors clear from dust, dirt and debris. They are particularly vulnerable to snow and ice, which can cause them to become stuck or slack and make it difficult for your patio doors to open and close.

Clean the track rails and rollers of sliding patio door repair doors by removing weather stripping that is dirty or damaged. Clean it, and then replace it. The same is true for rollers on patio doors, which can be wiped down and sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC French Doors, like sliding patios, are operated using 3 to 4, or sometimes, 5 point locking mechanisms. This includes the handle and lock cylinder that is operated by a key. These doors require maintenance, oiling of the moving parts. This can be done with an oil that is thin, but never WD40. This should be done at least once a year.

If sagging hinges don't cause the issue it could be because the door isn't aligned. It may be rubbing or catching the strike plate's opening in the frame. Remove the strike plate and employ a sharp tool enlarge the mortise. This allows the latch to fit perfectly in the hole, and also prevents rubbing or catching on the frame.

Once the cylinder is cleared of the way and out of the way, measure its width using an object or a piece of wood that will fit in the adjustment screw gap above the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, while the inner measurement runs from the center of the adjustment screw to the end of the cylinder.

Verify the lock's width

If your patio sliding door repair door latch isn't able to turn even after cleaning and oiling, it's possible that it is not aligned with the strike plate. Examine if the door is properly balanced and whether the hinge screws are tight however, in many instances shifting the strike plate up or down can fix the issue.

The latch may not engage properly when the strike of the lock is too small. In this case, enlarge the opening with an hammer and chisel. Then test the latch to ensure it doesn't rub against the door jamb frame or catch on it.

You must identify the kind of mortise lock you currently have before buying an alternative. You can do this by looking at the faceplate of the lock and determining if it is square or round. Then, take a look at the screw holes on the current lock and note the dimensions of each. This will enable you to locate a replacement lock that is the exact same width and will fit into the hole you have already.

You'll need to identify the mortise lock and inspect it for any bends, scratches or other damage that needs to be fixed. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if you notice indications of damage.

Once you've decided on the kind of lock replacement you require, it's now time to begin the actual repair. Remove the handle and spindle from your patio door, and then put in the new one. Start by putting in the handle in the interior by aligning it with the spindle and then securing it in place by using the two bolts or screws which hold it. Install the exterior handle following the interior handle. Once you have completed these steps, test the handles to make sure they open and shut easily and that the latch engages correctly with the strikeplate.

Check the Strike on the door.

The strike plate and the door latch are two parts which work together to secure the door. If these are misaligned and the latch doesn't latch the door properly. This problem is usually very easy to solve.

Check the holes for receiving of the strike plate to make sure they are free of obstructions like dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move horizontally, but not removing it from the door frame. Adjust the strike plate to align its receiving holes with the latch hooks of the door latch. After the strike plate has been adjusted tighten the screws, and test the door to determine if it shuts smoothly with the new adjustment.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are vital for locking and unlocking your door. These plates are usually placed on the top and bottom of the door jamb, where they support the door's latch. Then, the door latch is able to slide into the strike plate, creating the seal when it is closed. If the strike plate has been damaged or rusted or not properly installed the latch might not properly lock the door.

One common reason for a patio door lock to become stuck or not close is a misalignment between the latch and the strike plate. The easiest method to check for this is with the "lipstick test." Rub some lipstick on the edge of the deadbolt, then apply masking tape over it. The lipstick will leave a mark when you close the door. This will show you exactly where the latch connects to the strike plate. If the mark is too high or low it is possible to alter the strike plate.

If your patio door locks for sliding aren't functioning properly they could be a problem in keeping your home safe from burglars. You need to fix this problem as soon as possible. Follow these steps to repair your patio door lock and restore its function.