• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat key case replacement 500 Key Fob Won't Work

A fiat van Key replacement 500 key fob is a handy way to open the doors and begin the car. There are a myriad of reasons the fob won't work. This could be due to a dead coin-battery or water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat key case replacement Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason why the 500 key fob won't function is due to the battery is dead. Key fobs of today have a limited range of operation and must be within a few inches of your vehicle to work. If you're not close to your vehicle, and you press the key fob button the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one of a trusted brand like Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

You can test the battery of your coin-cell by pressing the buttons while standing close to your fiat 500x key fob programming 500. The parking lights should light up and the key fob should operate the lock and unlock switch.

If your key fiat fob isn't working after replacing the battery, there may be water damage which prevents it from communicating with the module in your vehicle. Water damage can happen in a variety of ways, such as simply splashing or submerging your key fob in saltwater at the beach. If you believe your fob was exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work the fob might need to be reset by a professional locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a machine. Saltwater is particularly dangerous to the circuit board of the fob, causing it to short out and eventually die. If you get the fob wet, it's not a good idea, but if you drop it into a cup of water or forget to remove it from your pocket before you run the washing machine and you don't have a chance, don't give in.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or a similar product. Check the fob again to check if it's working. If the key still doesn't work, it might need to be reprogrammed. This is usually done by a dealer or professional auto locksmith.

If the key is older and was not programmed to your vehicle It will most likely need to be replaced completely. This is a simple process that can be carried out by a professional automotive locksmith. The locksmith will require the fiat bravo key cut to match your car's ignition. They'll also have to reprogram the fob for the system of your car. This is an affordable and quick process that could be completed in the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far from your car, it will not respond to your commands. It is possible to remedy this by moving your remote closer to your vehicle until it responds.

If your fob won't work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button" or "button", it may be due to a malfunction on the internal circuit board. Reprogramming the fob typically resolves the issue. You can find directions on how to do this for most vehicles by searching YouTube or looking through the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they loose tension, they could stop the coin battery from being seated properly and can cause the remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle due to software issues or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances it is possible that the software will require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This can happen when the key fob is in proximity to radio transmitters (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob may not function because of a problem to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you might have a damaged receiver module on your 500. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's internal system including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will clear any residual electricity, and restart the computer of your car. This can help get your key fob working again. If the problem persists you should consult an expert technician. They can identify the root cause of any problems.