• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your pet come and go as they please without needing to let him in or out. They can also help keep your cat from having to go to the bathroom in the house.

Installing a cat flap into the door panel made of upvc is much easier than in glass doors, however it will require some expertise and the appropriate tools.

Take a look at the Door

Installing a cat door into a front door could be difficult, but so long as the cat flap is the right type and you follow the instructions, it shouldn't be too difficult. We will be showing you how to mark out the shape, using a jigsaw to cut out the door's area and then finish off the job by attaching the cat flap to the door. This will ensure that the flap stays in place and shields the door from wind and rain damaging the door.

To determine the size of the cat flap installation cost flap that you require, measure your pet's width. This will ensure that the flap is big enough that your pet can enter and leave the house without having to open or close the door each time, but it is also small enough to stop the pet from straying too far in either direction.

If your kit comes with an illustration of where to drill, then place it on the door, and then draw around it. If your door has moulding or a sill at the bottom, make sure you leave enough space between your cat and these elements.

Put on your eye protection as well as a dust mask. Then using a jigsaw begin to cut according to the lines you penciled in, but don't push the blade too hard because this will cause it to cut faster than you would like it to. If you have an already-cut square, make use of it to verify that you are cutting correctly and to ensure that the hole is a proper rectangle shape, once you are happy with this you can begin to remove the rest of the door material.

Draw a Line

The cat flap allows you to let your pet inside and outside without worrying about unwanted visitors or unwanted gifts. It also stops draughts and helps to keep the temperature in your home stable. However, putting the cat flap to your door can seem like an intimidating task for those who haven't done it before. This can lead many people to call an expert joiner or carpenter to do the job instead. It is an option, but you can do it yourself if the tools are right and the steps are followed.

This is much simpler to do on a wooden door, but it is still possible with uPVC. However it is important to be cautious not to scratch the doors as this could cause the door to be damaged and invalidate your warranty. First, you need to measure the door to ensure that it can accommodate the new cat-flap. This should be easy enough for the standard uPVC door, however you may require extra care if you are using an alternative kind of door, as they can be more difficult to cut than solid uPVC panels.

Next, you will need to determine the belly height of your cat. This is the height between the floor and the bottom of your cat's stomach. It is important to find an area at the entrance that will allow your pet to pass through comfortably. Once you have this information, you will need to mark out the area with pencil and a spirit level to be sure that the hole you make will be suitable for your cat.

After you've marked the area, it's now time to cut the hole. It is crucial to take your time and use a jigsaw in order to ensure that the cuts are clean and smooth, not rough and uneven. This could cause damage to your door. Be sure to wear safety glasses and a dust mask whenever using the jigsaw, as breathing in the dust could be harmful to your health. After you've finished the cutting, you will have to smooth the edges of the hole using sandpaper, so that your cat flap can be fitted easily.

Cut a Hole

Installing a cat flap to an existing door panel or double glazing sealed unit can be difficult. If you're not skilled in DIY, it is recommended to hire an expert to do the work for you. A faulty job can not only be unsightly and unattractive, but could also be an security risk. It could allow cold air to enter when the cat is outside and hot air to escape when the cat flap insulation is inside.

The first thing to do is mark the location of the hole in the door using a pencil and a spirit level, this will ensure that it is correctly placed and runs parallel to other parts of the door. Make sure you have sandpaper to smooth any rough edges.

Wear any safety gear you'll need to use the power tool. If you are concerned about the sound of a jigsaw you can buy one that is cordless, which is much quieter and easier to use.

It is important that you only cut away the material required to make the cat flap. It is necessary to leave a bit of material for the wall thickness of the Fitting Cat Flap In Upvc Door Panel flap. However cutting off too much material can cause problems or even damage the door frame.

A door made of upvc could contain a metal frame or a panel inside that could interfere with the microchip cat flap if this is the case you will need to cut an over-sized hole to ensure that the metal doesn't come into contact with the wall of the cat flap, if this is done, it is important to fill in the oversize gap and render it watertight.

If you're looking to install a cat flap in a double-glazed or upvc window cat flap with frames made of metal you'll need to talk to a specialist. They can provide you with a new piece of glass with the hole that is already designed for the cat flap. It is much less expensive to get this done rather than to attempt to fix a cat flap into an existing glass pane that was not designed specifically for the purpose.

Install the Flap

Cat flaps let your pet leave and come whenever they want, allowing them the freedom to lounge inside the house when they want to. If you've got an uPVC door, it might be difficult to install a cat flap, especially in the absence of a glass pane that can be cut to accommodate one. If you're willing to purchase and install a half-glazed replacement uPVC panel then it is possible to fit the cat flap to these doors. It's not as easy as simply making a hole in the door however, and there are some things you'll need to take care of first to ensure it's safe.

A composite, uPVC or GRP door panel is usually composed of a thin plastic skin which is bonded to an insulating polystyrene base. It is crucial to be careful when cutting the material. This type of door has a template you can use to cut the hole.

After you've marked the position of the hole in your door, it's now time to put in the cat flap. You can pick from a variety of designs, from simple push-button flaps to ones that are microchip-activated and allow only your pet to enter. Whatever kind of cat flaps you choose it is essential that your cat can use the flap comfortably without getting stuck in bad weather.

It's a good idea to opt for circular fittings rather than one that is square, because circles can be more securely cut into door glass. This is because square holes make the glass more susceptible to cracking if drills are used on it. It's also a much safer option as you're not putting yourself at risk by having to drill into toughened glass that might break and cause injury to your pet or your family. This is particularly important if there are children or elderly people in your home that could be hurt by glass shards.